Dd wrt v24 sp2 bridge setup
You CAN try using the same SSID but it usually will not work properly. Wireless Network Name(SSID) : Different from Primary Router Wireless Channel : Must Match Primary Router (This will disappear once you put it in RB mode, and isn't needed) Wireless Network Name(SSID) : Must Match Primary Router exactly including exact case- Make sure you spell this correctly Wireless Network Mode : Must Match Primary Router
DD WRT V24 SP2 BRIDGE SETUP PASSWORD
Newer versions of DD-WRT will require you to set a password before you can continue. The dd-wrt default wireless SSID is "dd-wrt" Otherwise leave your computer's network adaptor(s) programmed with the factory default setting of DHCP and the router will assign a valid address to your computer.Ĭonnect your computer to the secondary router via wired LAN port or as a wireless client.
DD WRT V24 SP2 BRIDGE SETUP HOW TO
Set your computer to a static IP of 192.168.1.9 if you know how to set static addresses. Restore Factory Defaults on Secondary (DD-WRT) Routerĭo a proper HARD 30-30-30 Reset on the router. The secondary router running DD-WRT v24 will be configured as the Repeater Bridge. To enable bridge mode between two routers, the primary router must be in AP mode (default) with DHCP Server enabled. This mode is NOT for WIRED connections between two routers! It is a wireless connection only. If you are using a G router, use 12548 builds to create a wireless bridge. (This will work for almost everything, but do check notes on individual routers below clock). I did find this info just in-case you did not ever see it from there web site and these settings are just for "wireless NOT wired"Ī very simple step-by-step description to connect a Router running selected DD-WRTV24 firmware in Repeater Bridge Mode. These are the instructions for your chipset you have. Is the primary router running DD-wrt and is so is it the version? What is the modem from your ISP is that a modem & router or is it just a modem. What is the make and model of your 1st primary router. your first (primary wireless router) how is that one set up and what is the IP set up: The router is set as a "router" with DHCP etc and if you are static what addressing are you using from your ISP? and for in-house you are (192.168.1.100 and subnet 255.255.255.0 and gateway 192.168.1.1 etc) The link you provided is V24 that supports wireless bridging! Who is your ISP? and do you have DSL, Cable, T1 etc and do you have a static IP or DHCP coming in. I know with a lot of Atheros-based chip that this is a option. OK I am sorry on you not being able to set it as a AP it must be a limitation of the Broadcom chipset and then DD doesn't enable it then. If anyone knows anything more about this than i do, or can point me to someone or some page that does, then please do, as i am eager to move some servers from the main workstation to another location without buying 50ft of Ethernet and running it through walls ext. It seems like i do for a temporary time when setting up the router/bridge/repeater, but that is lost as soon as i unplug the router from the computer i used to set up. Now, i would be happy to sacrifice the Repeater functionality of the device if i could gain the Bridge functionality of the device. Network Diagnostics says to match the options on the router with those of the adapter card of the computer, however, i am using the same settings for transmitting the data as the main router to begin with. I also receive the SSID of the repeater on another laptop at my workstation, but i am unable to connect. However, after fallowing the tutorial several times, and doing the 30/30/30 reset between each try, i had always either encountered the router's WAN address as either 0.0.0.0 or as the WAN was disabled, in either case, i was unable to use the Bridge and Repeater functions.Īlthough, when i sacrifice the Bridge option, the device gets a WAN address, and allows me to gain internet access from the computer i had hard-wired into the router to configure everything. I have a Cisco E1000 v1.0 router, and downloaded the firmware for such from the following site: Īfter typing in Cisco and selecting my router, i had the firmware, which i did successfully update, and begin using. This is all using a non-standard firmware for the router, as the router's default firmware does not offer these options. That particular post only provided a simple tutorial, and as I always do, i go look at more research.
![dd wrt v24 sp2 bridge setup dd wrt v24 sp2 bridge setup](https://forum.dd-wrt.com/phpBB2/files/router_settings_1_new_353.jpg)
Well, I was around on the internet, and was reading on a blog post about a router that was converted to a wireless network bridge, and can be used as a repeater. My previous post about the Addtron switch is still in need of answers. (I have learned that several servers running at the same time generate quite a bit of noise and must be moved somewhere convenient for that noise). Ok, so i have two different routers to use as bridge/repeaters to the network within my residence.